Counterbalance Forklift
News
  • What Kind of Electric Welding is Used to Replace The Bucket Teeth of The Loader?
    What Kind of Electric Welding is Used to Replace The Bucket Teeth of The Loader? Dec 12 , 2023
    1. Working principle of construction wheel loader Loaders can be divided into power systems, mechanical systems, hydraulic systems and control systems. As an organic whole, the performance of the loader is not only related to the performance of the mechanical part of the working device, but also related to the performance of the hydraulic system and control system. Power system: Loader power is ge...
    Read More
  • Troubleshooting and Maintenance of microcontroller-type forklifts
    Troubleshooting and Maintenance of microcontroller-type forklifts Dec 06 , 2023
    First, troubleshooting. The following troubleshooting checklist is specific to microcontroller warehouse forklift truck. Troubleshooting checklists, "time-of-operating" diagnostic instructions, "self" diagnostic tests, problem lists, and problem flow charts help: 1. Define the problem and check for existing problems. 2. Carry out inspections in a logical order. 3. Carry out necessary repairs. 4. C...
    Read More
  • Parts Composition and Principle of Forklift Braking System
    Parts Composition and Principle of Forklift Braking System Dec 01 , 2023
    Parts composition and principle of Rough Terrain Forklift Truck braking system 1. Brake control components: 1. Hydraulic Diesel Forklift brake drum; 2. Brake cam; 3. Brake shoe; 4. Rod; 5. Steering rod; 6. Return spring; 7. Pedal. When the brake pedal is applied lean, the brake shoes are connected to the brake drum attached to the forklift's drive motor. Then complete the braking operation. 2. Ser...
    Read More
  • How to adjust the height of forklift forks and masts
    How to adjust the height of forklift forks and masts Nov 17 , 2023
    How to adjust the height of forklift forks and masts 1. Move the mast so that the rear part is fully tilted. 2. Completely lower the fork. Bottom fork bearings, counterbalance diesel forklift bearings. 3. For fully free lifting and fully free triple lifting models, the bottom of the inner mast must be as high as the bottom of the fixed mast. 4. Measure the distance from the bottom of the inner col...
    Read More
  • How do I access the error codes stored on my forklift?
    How do I access the error codes stored on my forklift? Sep 20 , 2023
    How do I access the error codes stored on my forklift? Some series of all terrain forklifts can memorize the last 24 error codes. Helps a lot when the forklift is having intermittent problems and the operator doesn't remember which code appears on the display. Moreover, by analyzing the contents of the last 24 error codes, it is possible to determine what work the counterbalance lift truck has don...
    Read More
  • How to Install the Forklift Control Panel?
    How to Install the Forklift Control Panel? Aug 09 , 2023
    How to install the 16 ton forklift control panel? 1. Use a small amount of heat transfer compound on control panels and mating surfaces prior to assembly. 2. Use sealant on all screw threads used to reinforce parts on the control panel. 3. Use sealant on the screws used to tighten the positive and negative fins on the control panel to a torque of 10-14N.M, 90-125ib.in. 4. Tighten the nuts and scre...
    Read More
  • Forklift Chassis Resistance Inspection and Maintenance
    Forklift Chassis Resistance Inspection and Maintenance Jul 17 , 2023
    Rough Terrain Forklift chassis resistance inspection and maintenance 1. Chassis resistance inspection. The resistance of any part between the forklift wiring and the chassis should be at least 1000 ohms. Many failures are caused by chassis short circuits. Usually, there are two faults before a fault occurs. However, since the battery can have chassis leaks, even a single short in the forklift wiri...
    Read More
  • How to adjust the height of forklift fork and mast
    How to adjust the height of forklift fork and mast Jul 05 , 2023
    How to adjust the height of counterbalanced diesel forklift fork and mast 1. Move the mast so that the rear is fully tilted. 2. Completely lower the fork. Bottom yoke bearings, forklift bearings. 3. For the full free lift and full free triple lift models, the bottom of the inner mast must be as high as the bottom of the fixed mast. 4. Measure the distance from the bottom of the inner column to the...
    Read More
1 ... 3 4 5 6 7 ... 14
[  A total of  14  pages]
Leave A Message

Leave A Message

    If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

About

contact